Vaisala WXT520 Podręcznik Użytkownika Strona 138
- Strona / 171
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
User’s Guide ______________________________________________________________________
136 _________________________________________________________________ M210906EN-C
0xUabc!0TX,Use chksum CCb<cr><lf> (wrong checksum applied to
the 0xU command)
See also Chapter 10, Troubleshooting, on page 133. In case of constant
error, please contact Vaisala Service Center, see Vaisala Service
Centers on page 131.
Table 11 Error Messaging/Text Messages Table
Text message
identifier (in
NMEA 0183 v3.0
protocol only)
Text Message Interpretation and action
01 Unable to measure error The requested parameters are not activated in the
message, see Chapter 8, Sensor and Data Message
Settings, on page 107, and check the parameter
selection fields.
02 Sync/address error The device address in the beginning of the command is
invalid. Ask the device address with the ?! (SDI-12) or
?<cr><lf> (ASCII and NMEA) command and retype the
command with the correct address.
03 Unknown cmd error The command is not supported, use the correct
command format, see Chapter 7, Getting the Data
Messages, on page 65.
04 Profile reset Checksum error in configuration settings during power-
up. Factory settings used instead.
05 Factory reset Checksum error in calibration settings during power-up.
Factory settings used instead.
06 Version reset New software version in use.
07 Start-up Software reset. Program starts from the beginning.
08 Use chksum xxx Given checksum not correct for the command. Use the
proposed checksum.
09 Measurement reset The ongoing measurement of all the sensors interrupted
and started from the beginning.
10 Rain reset The precipitation sensor counter reset.
11 Inty reset Precipitation sensor intensity counter reset.
NOTE
When WXT520 is used on an RS-485 bus with other polled devices,
the error messaging feature shall always be disabled. This is done by
the following command: 0SU,S=N<crlf>.
- USER'S GUIDE 1
- Table of Contents 3
- CHAPTER 8 5
- CHAPTER 9 5
- APPENDIX E 7
- List of Figures 9
- List of Tables 11
- GENERAL INFORMATION 13
- General Safety Considerations 14
- Trademarks 16
- License Agreement 16
- Regulatory Compliance 16
- Warranty 17
- PRODUCT OVERVIEW 19
- Heating Function 20
- WXT520 Transmitter Components 21
- 0803-028 22
- 0505-193 24
- 0804-022 24
- 0806-001 26
- 0.5 L 1 t 28
- PTU Measurement Principle 31
- Heating (Optional) 31
- 0806-010 32
- Selecting the Location 34
- 0712-009 35
- 0803-030 37
- 0803-032 39
- Grounding the WXT520 40
- Marine Grounding Jumper 41
- 0803-048 42
- Wind Direction Offset 44
- WIRING AND POWER MANAGEMENT 45
- 0805-023 46
- External Wiring 48
- Internal Wiring 49
- 0803-035 50
- Data Communication Interfaces 52
- Power Management 53
- CONNECTION OPTIONS 57
- Connection cables 58
- Service Cable Connection 60
- Connector or Screw Terminal 61
- Checking the Current 62
- Communication Settings (aXU) 62
- Changing the Communication 65
- Settings (aXU) 65
- GETTING THE DATA MESSAGES 67
- General Commands 68
- Reset (aXZ) 68
- Precipitation Counter Reset 69
- Measurement Reset (aXZM) 71
- ASCII Protocol 72
- Abbreviations and Units 72
- Device Address (?) 73
- Wind Data Message (aR1) 74
- Pressure, Temperature and 75
- Humidity Data Message (aR2) 75
- Supervisor Data Message (aR5) 77
- Combined Data Message (aR) 78
- Composite Data Message Query 78
- Polling with CRC 79
- SDI-12 Protocol 82
- Address Query Command (?) 83
- Change Address Command (aAb) 84
- CRC (aMC) 87
- CRC (aCC) 88
- Send Data Command (aD) 89
- Examples of aM, aC and aD 90
- Commands 90
- Continuous Measurement (aR) 92
- NMEA 0183 V3.0 Protocol 95
- MWV Wind Speed and Direction 96
- XDR Transducer Measurement 98
- TXT Text Transmission 106
- Automatic Mode 108
- Automatic Composite Data 108
- Message (aR0) 108
- SENSOR AND DATA MESSAGE 109
- SETTINGS 109
- Setting Fields 111
- Changing the Settings (aWU) 113
- Checking the Settings (aTU) 115
- Changing the Settings (aTU) 117
- Precipitation Sensor 119
- Checking the Settings (aRU) 119
- Changing the Settings (aRU) 123
- Supervisor Message 125
- Checking the Settings (aSU) 125
- Changing the Settings (aSU) 127
- Composite Data Message (aR0) 129
- 0R0<cr><lf> 130
- MAINTENANCE 131
- Replacing the PTU Module 132
- Vaisala Service Centers 133
- TROUBLESHOOTING 135
- Self-Diagnostics 137
- Error Messaging/Text Messages 137
- Rain and Wind Sensor Heating 139
- Operating Voltage Control 139
- Technical Support 139
- TECHNICAL SPECIFICATIONS 141
- Tab le 14 Wi nd 142
- Table 15 Relative Humidity 143
- Table 16 Precipitation 143
- Inputs and Outputs 144
- Operating Conditions 145
- Materials 146
- Options and Accessories 147
- Dimensions (mm/inch) 148
- 0805-013 149
- 0505-211 150
- Communication Protocol 152
- RS-485 Serial Interface 153
- ASCII, Polled 153
- NMEA 0183 v3.0, Query 154
- Query Commands 156
- SDI-12 PROTOCOL 159
- SDI-12 Timing 161
- CRC-16 COMPUTATION 163
- WIND MEASUREMENT AVERAGING 165
- 0505-215 166
- General Unit Settings 168
- Wind Configuration Settings 168
- PTU Configuration Settings 169
- Rain Configuration Settings 169
- Supervisor Settings 169
- *M210906EN* 171
Powiązane produkty i podręczniki dla Pomiary, testowanie i kontrola Vaisala WXT520
(130 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.020 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji